We extend EIP-170 by introducing a maximum size limit for initcode (MAX_INITCODE_SIZE = 2 * MAX_CODE_SIZE = 49152).
Furthermore, we introduce a charge of 2 gas for every 32-byte chunk of initcode to represent the cost of jumpdest-analysis.
Lastly, the size limit results in the nice-to-have property that EVM code size, code offset (PC), and jump offset fits a 16-bit value.
During contract creation the client has to perform jumpdest-analysis on the initcode prior to execution. The work performed scales linearly with the size of the initcode. This work currently is not metered, nor is there a protocol enforced upper bound for the size.
There are three costs charged today:
initcode: 4 gas for a byte with the value of zero, and 16 gas otherwise.CREATE2 only: 6 gas per word.Only the first cost applies to initcode, but only in the case of contract creation transactions. For the case of CREATE/CREATE2 there is no such cost, and it is possible to programmatically generate variations of initcode in a relatively cheap manner. In the past it was possible to craft malicious initcode due to a vulnerability fixed in 2017 by geth 1.6.5.
Furthermore, the lack of a limit has caused lengthy discussions for some EVM proposals, influencing the design, or even causing a delay or cancellation of a feature.
We are motivated by three reasons:
initcode is fairly charged (most importantly cost is proportional to initcode's length) to minimize the risks for the future.PC), and jump offsets fit 16-bits).| Constant | Value |
|---|---|
INITCODE_WORD_COST |
2 |
MAX_INITCODE_SIZE |
2 * MAX_CODE_SIZE |
Where MAX_CODE_SIZE is defined by EIP-170 as 24576.
We define initcode_cost(initcode) to equal INITCODE_WORD_COST * ceil(len(initcode) / 32).
initcode) in a create transaction exceeds MAX_INITCODE_SIZE, transaction is invalid. (Note that this is similar to transactions considered invalid for not meeting the intrinsic gas cost requirement.)initcode_cost(initcode). (Note that this is included in transaction intrinsic cost, i.e. transaction with not enough gas to cover initcode cost is invalid.)initcode to CREATE or CREATE2 instructions exceeds MAX_INITCODE_SIZE, instruction execution exceptionally aborts (as if it runs out of gas).CREATE and CREATE2 instructions charge an extra gas cost equaling to initcode_cost(initcode). This cost is deducted before the calculation of the resulting contract address and the execution of initcode. (Note that this means before or at the same time as the hashing cost is applied in CREATE2.)The value of INITCODE_WORD_COST is selected based on performance benchmarks of differing worst-cases per implementation. The baseline for the benchmarks is the performance of KECCAK256 hashing in geth 1.10.9, which matches the 70 Mgas/s gas limit target on a 4.0 GHz x86_64 CPU.
| EVM | version | MB/s | B/CPUcycle | CPUcycle/B | cost of 1 B | cost of 32 B |
|---|---|---|---|---|---|---|
| geth/KECCAK256 | 1.10.9 | 357 | 1.8 | 0.6 | 0.2 | 6.0 |
| geth | 1.10.9 | 1091 | 5.5 | 0.2 | 0.1 | 2.0 |
| evmone/Baseline | 0.8.2 | 727 | 3.7 | 0.3 | 0.1 | 2.9 |
| evmone/Advanced | 0.8.2 | 155 | 0.8 | 1.3 | 0.4 | 13.8 |
We have chosen the cost of 2 gas per word based on Geth's implementation and comparing with KECCAK256 performance. This means the per byte cost is 0.0625. While fractional gas costs are not permitted in the EVM, we can approximate it by charging per-word.
Moreover, calculating gas per word is compatible with the calculation of CREATE2's hashcost of EIP-1014. Therefore, the same implementation may be used for CREATE and CREATE2 with different cost constants: before activation 0 for CREATE and 6 for CREATE2, after activation 2 for CREATE and 6 + 2 for CREATE2.
Estimating and creating worst case scenarios is easier with an upper bound in place, given one parameter for the search is greatly reduced. This allows for selecting a much more optimistic gas per byte.
Should there be no upper bound, the cost would need to be higher accounting for unknown unknowns. Given most initcode (TODO: state maximum initcode size resulting in deployment seen on mainnet here) does not exceed the proposed limit, penalising contracts by overly conservative costs seems unnecessary.
In most, if not all cases when a new contract is being created, the resulting runtime code is copied from the initcode itself. For the basic case the 2 * MAX_CODE_SIZE limit allows MAX_CODE_SIZE for runtime code and another MAX_CODE_SIZE for contract constructor code. However, the limit may have practical implications for cases where multiple contracts are deployed in a single create transaction.
The initcode cost for create transaction data (0.0625 gas per byte) is negligible compared to the transaction data cost (4 or 16 gas per byte). Despite that, we decided to include it in the specification for consistency, and more importantly for forward compatibility.
We specified that initcode size limit violation for CREATE/CREATE2 results in exceptional abort of the execution. This places it in the group of early out-of-gas checks, including: stack underflow, memory expansion, static call violation, initcode hashing cost, and initcode cost introduced by this EIP. They precede the later "light" checks: call depth and balance. The choice gives consistency to the order of checks and lowers implementation complexity (out-of-gas checks can be performed in any order).
This EIP requires a "network upgrade", since it modifies consensus rules.
Already deployed contracts should not be effected, but certain transactions (with initcode beyond the proposed limit) would still be includable in a block, but result in an exceptional abort.
Tests should include the following cases:
CREATE/CREATE2/creation transaction with len(initcode) at MAX_INITCODE_SIZECREATE/CREATE2/creation transaction with len(initcode) at MAX_INITCODE_SIZE+1For client implementations, this EIP makes attacks based on jumpdest-analysis less problematic, so should increase the robustness of clients.
For layer 2, this EIP introduces failure-modes where there previously were none. There could exist factory-contracts which deploy multi-level contract hierarchies, such that the code for multiple contracts are included in the initcode of the first contract. The author(s) of this EIP are not aware of any such contracts.
Currently, on London, with 30M gas limit, it would be possible to trigger jumpdest-analysis of a total ~1.3GB of initcode. With this EIP, the cost for such an attack would increase by roughly 80M gas.
Copyright and related rights waived via CC0.